ACX wants every file to average between −23 and −18 dB RMS. Below −23 dB, your voice is too quiet. Raise it to about −20 dB with an RMS loudness setting, cap the peaks at −3 dB with a limiter, then check the noise floor is still below −60 dB.
The number ACX allows
| ACX allows | −23 to −18 dB RMS |
|---|---|
| Aim for | about −20 dB RMS |
| ChapterBooth masters to | −19.5 dB RMS |
RMS is the average level of the whole file, quiet gaps included. It is the number ACX calls “volume”. It is different from the peak, which is the single loudest moment.
How to measure it
Drop the file on the free ACX Check. It measures RMS, peaks and noise floor in your browser, without uploading the file, and names the biggest problem first with your number. Drop every chapter at once to see the whole book in one table.
Why it happens
- You sit too far from the mic. A hand’s width away is about right.
- The input gain is set low to stay safe from clipping.
- You read quietly, as people do late at night in a closet.
The catch: every dB you add to your voice is added to the noise. A file at −28 dB RMS with a −62 dB floor ends up at −20 dB RMS with a −54 dB floor. The level passes and the noise floor now fails.
Fix it in Audacity
- Select the whole track (Ctrl+A, or Cmd+A on a Mac).
- Open Effect › Volume and Compression › Loudness Normalization. Choose RMS, set −20 dB, and apply.
- Open Effect › Volume and Compression › Limiter. Set the threshold and the make‑up target to −3.5 dB, and apply. Older versions have one setting, Limit to: set it to −3.5 dB.
- Check the file again. The limiter lowers the average a little; if RMS is now below −23 dB, repeat at −19 dB.
- If the noise floor fails, clean it gently. The noise floor guide has the settings.
Fix it in ChapterBooth
Drop the file on the ACX Check and press Fix it free, or upload the chapter in the studio. ChapterBooth removes the noise first, then raises your voice to −19.5 dB RMS and limits peaks to −3.5 dB, so the floor stays below −60 dB. You hear the first minute in about three minutes. The first 45 minutes of finished audio are free.
If a recording is too quiet to save without lifting the noise past repair, the check says so and tells you what to change before you record again.
What not to do
- Don’t use Normalize for this. Audacity’s Normalize sets the loudest peak, not the average, so RMS barely moves.
- Don’t turn it up, then scrub the noise hard. Heavy noise reduction sounds watery and fails the listening check instead.
- Don’t raise the input gain until it clips. Move closer to the mic instead. Clipping can’t be undone; see peaks too high.
Every rule on one page: ACX requirements in plain English. Every rejection reason: why ACX rejects audiobooks.
Questions
What RMS should I aim for on ACX?
About −20 dB. Anything from −23 to −18 dB passes, but the middle leaves room for the limiter and for small differences between chapters.
Why did my noise floor fail after I fixed the RMS?
Raising the level raises everything, including the room. Every dB you add to your voice is added to the hum and hiss too. Clean the noise, or record closer so you need less gain.
Is RMS the same as LUFS?
No. ACX measures RMS in dB. LUFS weights the sound the way ears hear it. In Audacity’s Loudness Normalization, choose RMS, not perceived loudness.
Does ACX check RMS per file or for the whole book?
Per file. Every file you upload, including the credits and the retail sample, must average between −23 and −18 dB RMS.
Sources
- ACX, “What are the ACX audio submission requirements?”, dated 15 April 2026: help.acx.com, read 12 November 2026.